KeepRite mini split error code EF
Intelligent eye (occupancy sensor) module error.
- TypeFault
- SystemControl board
- Can I fix it?Usually a homeowner fix
- Applies toDLC/DLF series, 2015 and later (Midea-built)
What EF means on a KeepRite
On units with an occupancy sensor (the 'intelligent eye' that sets back the temperature when the room is empty), the sensor module failed its self-check. Heating and cooling keep working.
On this platform, EF is a fault: something has failed or is disconnected and needs diagnosis.
Common causes
- A loose sensor module plug.
- A dirty or blocked sensor window.
- A failed sensor module.
How to fix it yourself
You can almost always clear this yourself with the steps below.
- Turn the follow-me / intelligent-eye function off from the remote to keep using the unit normally.
- Reset the system: switch the breaker (or the outdoor disconnect) off, wait a full five minutes so the boards fully discharge, then switch it back on and restart from the remote.
- With power off, reseat the sensor module plug behind the front panel.
Switch off power at the breaker before opening either unit. Capacitors in the outdoor unit hold a charge for several minutes after power is cut.
When to call a technician
Optional repair; the unit works without the sensor.
Which KeepRite units show EF
This page applies to KeepRite DLCSRA / DLCSRB / DLCLRA outdoor with DLFSHA / DLFSFA indoor (2015 and later) and DLC4 / DLF4 (2013 to 2015) units on the DLC/DLF series, 2015 and later (Midea-built). KeepRite's own documentation lists EF as "Intelligent eye (occupancy sensor) module error", the same definition used across the Midea platform (classic codes) it is built on. If your unit shows a code with a different shape (for example a four-character code, or a plain number), it is from a different table; use the lookup with your exact code.
Where KeepRite shows this code
DLC/DLF series, 2015 and later (Midea-built): The code appears on the indoor unit's LED display in place of the set temperature. Some models also blink the indicator lamps in a pattern that matches the code. E codes are faults in the indoor unit or its communication link, F codes are faults on the outdoor side, and P codes are protections: the outdoor unit has stopped itself to prevent damage. EC is the refrigerant leak check.
Other KeepRite codes
Same part of the system as EF:
EF on other brands
The same characters do not always mean the same thing. Check the brand on your unit.
- Pioneer EF Intelligent eye (occupancy sensor) module error
- Zone Air EF Outdoor DC fan motor fault
- ACiQ EF Intelligent eye (occupancy sensor) module error / Outdoor DC fan motor fault
Questions people ask
Can I reset a KeepRite EF code myself?
Yes. Turn the system off at the breaker for five minutes, then restart it. If EF comes back, the fault is real and needs the checks above.
Is it safe to keep running a KeepRite showing EF?
The unit will usually refuse to run, or run with reduced output, until the fault is cleared. Repeated resets do not fix anything and can mask a problem that is getting worse.
Do I need a technician for KeepRite EF?
You can almost always clear this yourself with the steps below. Optional repair; the unit works without the sensor.
Sources
- ICP DLCSRA Outdoor Unit Single Zone Ductless Service Manual 32808000801 (error code table)
- ICP ductless installation instructions IM-KSAIC04-04 (DLCPRA / DLCSRB / DLCERB / DLCLRA error codes)
- ICP R-410A Ductless Split System Service Manual 421 01 9204 00 (DLC4 / DLF4, 2013)
Updated September 2026. Codes and definitions vary by model year. If your manual disagrees with this page, your manual wins. Send a correction.