DIY HVAC Tools

ACiQ mini split code CL

Filter cleaning reminder. Also shown as CF, FC.

  • TypeStatus, not a fault
  • SystemDisplay
  • Can I fix it?Usually a homeowner fix
  • Applies tostandard single-zone and multi-zone (ACiQ-09Z-HP…, Midea-built)

What CL means on a ACiQ

A run-hour timer has expired and the unit is reminding you to clean the filters. Nothing is wrong; the unit keeps running.

On this platform, CL is a status, not a fault: the unit is telling you what it is doing; nothing is wrong.

What to do

You can almost always clear this yourself with the steps below.

  1. Wash the mesh filters behind the front panel, let them dry, and reinstall.
  2. Clear the reminder using the remote: on most models press and hold the LED or Reset button (see your manual), or turn the unit off and back on with the remote.

When to call a technician

This is not a fault. No technician is needed unless it will not clear.

Which ACiQ units show CL

This page applies to ACiQ Standard single-zone (ACiQ-09Z-HP…B / W-HP) and multi-zone and K-series (ACiQ-K09W-HP…, SZDM / WHP / KZHP) units on the standard single-zone and multi-zone (ACiQ-09Z-HP…, Midea-built). ACiQ's own documentation lists CL as "Filter cleaning reminder", the same definition used across the Midea platform (classic codes) it is built on. If your unit shows a code with a different shape (for example a four-character code, or a plain number), it is from a different table; use the lookup with your exact code.

Where ACiQ shows this code

standard single-zone and multi-zone (ACiQ-09Z-HP…, Midea-built): The code appears on the indoor unit's LED display in place of the set temperature. Some models also blink the indicator lamps in a pattern that matches the code. E codes are faults in the indoor unit or its communication link, F codes are faults on the outdoor side, and P codes are protections: the outdoor unit has stopped itself to prevent damage. EC is the refrigerant leak check.

Other ACiQ codes

Same part of the system as CL:

dFDefrost cycle runningAPWi-Fi pairing (access point) mode
E0Indoor unit EEPROM parameter error / Communication error between indoor and outdoor unitsE1Communication error between indoor and outdoor units / Indoor room temperature sensor fault (open or short circuit)E2Zero-crossing signal detection error / Indoor fan coil (evaporator) temperature sensor fault (open or short circuit)E3Indoor fan speed out of control (indoor fan motor fault) / Outdoor fan coil (condenser) temperature sensor fault (open or short circuit)E4Indoor room temperature sensor (T1) open or short circuit / Abnormal system operation or lack of refrigerantE5Evaporator coil temperature sensor (T2) open or short circuit / Model configuration or mismatch errorECRefrigerant leak detected (low refrigerant charge) / Outdoor module communication faultF0Overload current protection (compressor over-current) / Infrared (remote receiver) sensor fault

All ACiQ error codes

CL on other brands

The same characters do not always mean the same thing. Check the brand on your unit.

Questions people ask

Is CL on a ACiQ mini split an error?

No. CL is a status message: filter cleaning reminder. A run-hour timer has expired and the unit is reminding you to clean the filters.

Do I need a technician for ACiQ CL?

You can almost always clear this yourself with the steps below. This is not a fault. No technician is needed unless it will not clear.

Sources

  • ACiQ Standard Single-Zone Mini Split Service Manual (SZ-Z-HP / W-HP), Quick Maintenance by Error Code
  • ACiQ Mini-Split Air Handler and Condenser Service Manual (MS-SZDM / WHP / KZHP), error code table

Updated September 2026. Codes and definitions vary by model year. If your manual disagrees with this page, your manual wins. Send a correction.