Comfortmaker mini split error code EB
Communication error between indoor main board and display board. Also shown as Eb.
- TypeFault
- SystemCommunication
- Can I fix it?Homeowner checks, then maybe a tech
- Applies toDLC/DLF series, 2015 and later (Midea-built)
What EB means on a Comfortmaker
The indoor main board and the front display board stopped talking. The unit may keep running while the display or buttons misbehave.
On this platform, EB is a fault: something has failed or is disconnected and needs diagnosis.
Common causes
- A loose ribbon cable between the main board and the display.
- Moisture or corrosion on the display connector.
- A failed display board.
How to fix it yourself
Work through the checks below first; they resolve most cases. If they do not, the repair itself may need a technician.
- Reset the system: switch the breaker (or the outdoor disconnect) off, wait a full five minutes so the boards fully discharge, then switch it back on and restart from the remote.
- With power off, open the front panel and reseat the display cable at both ends.
Switch off power at the breaker before opening either unit. Capacitors in the outdoor unit hold a charge for several minutes after power is cut.
When to call a technician
A display board is a cheap part; a technician can confirm which board failed.
Which Comfortmaker units show EB
This page applies to Comfortmaker DLCSRA / DLCSRB / DLCLRA outdoor with DLFSHA / DLFSFA indoor (2015 and later) and DLC4 / DLF4 (2013 to 2015) units on the DLC/DLF series, 2015 and later (Midea-built). Comfortmaker's own documentation lists EB as "Communication error between indoor main board and display board", the same definition used across the Midea platform (classic codes) it is built on. If your unit shows a code with a different shape (for example a four-character code, or a plain number), it is from a different table; use the lookup with your exact code.
Where Comfortmaker shows this code
DLC/DLF series, 2015 and later (Midea-built): The code appears on the indoor unit's LED display in place of the set temperature. Some models also blink the indicator lamps in a pattern that matches the code. E codes are faults in the indoor unit or its communication link, F codes are faults on the outdoor side, and P codes are protections: the outdoor unit has stopped itself to prevent damage. EC is the refrigerant leak check.
Other Comfortmaker codes
Same part of the system as EB:
EB on other brands
The same characters do not always mean the same thing. Check the brand on your unit.
- Pioneer EB Communication error between indoor main board and display board
- Zone Air Eb Main board to LED display communication fault
- Mitsubishi Electric Eb Miswiring of indoor/outdoor connecting wires
- Trane Eb Main board to LED display communication fault / Miswiring of indoor/outdoor connecting wires
- ACiQ EB Communication error between indoor main board and display board / Main board to LED display communication fault
Questions people ask
Can I reset a Comfortmaker EB code myself?
Yes. Turn the system off at the breaker for five minutes, then restart it. If EB comes back, the fault is real and needs the checks above.
Is it safe to keep running a Comfortmaker showing EB?
The unit will usually refuse to run, or run with reduced output, until the fault is cleared. Repeated resets do not fix anything and can mask a problem that is getting worse.
Do I need a technician for Comfortmaker EB?
Work through the checks below first; they resolve most cases. If they do not, the repair itself may need a technician. A display board is a cheap part; a technician can confirm which board failed.
Sources
- ICP DLCSRA Outdoor Unit Single Zone Ductless Service Manual 32808000801 (error code table)
- ICP ductless installation instructions IM-KSAIC04-04 (DLCPRA / DLCSRB / DLCERB / DLCLRA error codes)
- ICP R-410A Ductless Split System Service Manual 421 01 9204 00 (DLC4 / DLF4, 2013)
Updated September 2026. Codes and definitions vary by model year. If your manual disagrees with this page, your manual wins. Send a correction.