DIY HVAC Tools

Comfortmaker mini split code AP

Wi-Fi pairing (access point) mode.

  • TypeStatus, not a fault
  • SystemDisplay
  • Can I fix it?Usually a homeowner fix
  • Applies toDLC/DLF series, 2015 and later (Midea-built)

What AP means on a Comfortmaker

The unit's Wi-Fi module is broadcasting its own network so the app can connect and configure it. It shows AP during setup, and sometimes after a power interruption if the module reboots.

On this platform, AP is a status, not a fault: the unit is telling you what it is doing; nothing is wrong.

What to do

You can almost always clear this yourself with the steps below.

  1. Finish pairing in the manufacturer's app, or wait; the unit exits AP mode on its own after several minutes.
  2. To force it out, turn the unit off and on with the remote.

When to call a technician

This is not a fault. No technician is needed unless it will not clear.

Which Comfortmaker units show AP

This page applies to Comfortmaker DLCSRA / DLCSRB / DLCLRA outdoor with DLFSHA / DLFSFA indoor (2015 and later) and DLC4 / DLF4 (2013 to 2015) units on the DLC/DLF series, 2015 and later (Midea-built). Comfortmaker's own documentation lists AP as "Wi-Fi pairing (access point) mode", the same definition used across the Midea platform (classic codes) it is built on. If your unit shows a code with a different shape (for example a four-character code, or a plain number), it is from a different table; use the lookup with your exact code.

Where Comfortmaker shows this code

DLC/DLF series, 2015 and later (Midea-built): The code appears on the indoor unit's LED display in place of the set temperature. Some models also blink the indicator lamps in a pattern that matches the code. E codes are faults in the indoor unit or its communication link, F codes are faults on the outdoor side, and P codes are protections: the outdoor unit has stopped itself to prevent damage. EC is the refrigerant leak check.

Other Comfortmaker codes

Same part of the system as AP:

dFDefrost cycle runningCLFilter cleaning reminderFoRefrigerant recovery (pump-down) modeH1Defrost cycle runningF7Oil return cycle (cooling)
E0Indoor unit EEPROM parameter errorE1Communication error between indoor and outdoor units / High pressure protectionE2Zero-crossing signal detection error / Indoor anti-freeze protectionE3Indoor fan speed out of control (indoor fan motor fault) / Low pressure protection (refrigerant shortage or blockage)E4Indoor room temperature sensor (T1) open or short circuit / Compressor discharge temperature too highE5Evaporator coil temperature sensor (T2) open or short circuit / Over-current protectionECRefrigerant leak detected (low refrigerant charge)F0Overload current protection (compressor over-current) / Refrigerant shortage or system blockage detected

All Comfortmaker error codes

AP on other brands

The same characters do not always mean the same thing. Check the brand on your unit.

Questions people ask

Is AP on a Comfortmaker mini split an error?

No. AP is a status message: wi-Fi pairing (access point) mode. The unit's Wi-Fi module is broadcasting its own network so the app can connect and configure it.

Do I need a technician for Comfortmaker AP?

You can almost always clear this yourself with the steps below. This is not a fault. No technician is needed unless it will not clear.

Sources

  • ICP DLCSRA Outdoor Unit Single Zone Ductless Service Manual 32808000801 (error code table)
  • ICP ductless installation instructions IM-KSAIC04-04 (DLCPRA / DLCSRB / DLCERB / DLCLRA error codes)
  • ICP R-410A Ductless Split System Service Manual 421 01 9204 00 (DLC4 / DLF4, 2013)

Updated September 2026. Codes and definitions vary by model year. If your manual disagrees with this page, your manual wins. Send a correction.