Arcoaire mini split error code H3
Compressor overload protection.
- TypeProtection
- SystemCompressor / inverter
- Can I fix it?Homeowner checks, then maybe a tech
- Applies toDLC4 / DLF4 series, 2013 to 2015 (Gree-built)
What H3 means on a Arcoaire
The compressor's overload protector opened because it got too hot or drew too much current.
On this platform, H3 is a protection: the system stopped or throttled itself to prevent damage; many clear on their own once conditions return to normal.
Common causes
- A blocked outdoor coil or failed fan.
- Low refrigerant charge.
- A restricted line set or closed valve.
- A failing compressor.
How to fix it yourself
Work through the checks below first; they resolve most cases. If they do not, the repair itself may need a technician.
- Look at the outdoor unit: clear leaves, cottonwood fluff, snow or ice from the coil and make sure the fan can spin freely and nothing is stacked against the cabinet.
- Let it cool with power off for 30 to 60 minutes.
- Confirm both service valves are fully open.
- Anything inside the refrigerant circuit (sensors are fine, but valves, compressors and leaks are not) needs EPA-certified refrigerant handling. That is a technician job.
Switch off power at the breaker before opening either unit. Capacitors in the outdoor unit hold a charge for several minutes after power is cut.
When to call a technician
If it returns with a clean coil and running fan, a technician should check charge and compressor current.
Which Arcoaire units show H3
This page applies to Arcoaire DLCSRA / DLCSRB / DLCLRA outdoor with DLFSHA / DLFSFA indoor (2015 and later) and DLC4 / DLF4 (2013 to 2015) units on the DLC4 / DLF4 series, 2013 to 2015 (Gree-built). Arcoaire's own documentation lists H3 as "Compressor overload protection", the same definition used across the Gree platform it is built on. If your unit shows a code with a different shape (for example a four-character code, or a plain number), it is from a different table; use the lookup with your exact code.
Where Arcoaire shows this code
DLC4 / DLF4 series, 2013 to 2015 (Gree-built): The code shows on the indoor unit's display in place of the temperature. If the display is off, press the Light button on the remote. Some models also count out the code as indicator blinks. E codes are system protections and faults, F codes are mostly sensor faults, H codes are outdoor and compressor protections, U codes are motor and valve faults, and P codes are power-supply faults.
Other Arcoaire codes
Same part of the system as H3:
H3 on other brands
The same characters do not always mean the same thing. Check the brand on your unit.
- Blueridge H3 Compressor overload protection
- Daikin H3 High-pressure switch fault
Questions people ask
Can I reset a Arcoaire H3 code myself?
Yes. Turn the system off at the breaker for five minutes, then restart it. If H3 comes back, the fault is real and needs the checks above.
Is it safe to keep running a Arcoaire showing H3?
Not repeatedly. A protection code means the unit stopped itself to prevent damage, and resetting it over and over can turn a cheap repair into a compressor failure. Reset once, check the basics, and stop if it returns.
Do I need a technician for Arcoaire H3?
Work through the checks below first; they resolve most cases. If they do not, the repair itself may need a technician. If it returns with a clean coil and running fan, a technician should check charge and compressor current.
Sources
- ICP DLCSRA Outdoor Unit Single Zone Ductless Service Manual 32808000801 (error code table)
- ICP ductless installation instructions IM-KSAIC04-04 (DLCPRA / DLCSRB / DLCERB / DLCLRA error codes)
- ICP R-410A Ductless Split System Service Manual 421 01 9204 00 (DLC4 / DLF4, 2013)
Updated September 2026. Codes and definitions vary by model year. If your manual disagrees with this page, your manual wins. Send a correction.